Indo-US MIM Tec Pvt Ltd earned the grand prize in the automotive – engine category for these four MIM parts  that go into a device that controls fuel flow in GDI pumps.
Indo-US MIM Tec Pvt Ltd earned the grand prize in the automotive – engine category for these four MIM parts that go into a device that controls fuel flow in GDI pumps.
FloMet LLC, an ARCMIM company located in DeLand, Florida, earned the grand prize in the medical/dental category for two 5 mm tines – one fixed, one moving – that go into a thermal tissue fusion and dissection system made by its customer.
FloMet LLC, an ARCMIM company located in DeLand, Florida, earned the grand prize in the medical/dental category for two 5 mm tines – one fixed, one moving – that go into a thermal tissue fusion and dissection system made by its customer.
Keystone Powdered Metal Co, based in St Marys, Pennsylvania, was awarded grand prize in the automotive – transmission category for a planetary carrier assembly made for its customer, Ford Motor Company.
Keystone Powdered Metal Co, based in St Marys, Pennsylvania, was awarded grand prize in the automotive – transmission category for a planetary carrier assembly made for its customer, Ford Motor Company.
A three-piece assembly also made by FloMet LLC for Shure Incorporated won the grand prize in the electronic/electrical components category.
A three-piece assembly also made by FloMet LLC for Shure Incorporated won the grand prize in the electronic/electrical components category.
Capstan, from Wrentham, Massachusetts, received the grand prize in the lawn & garden/off-highway category for copper-steel parts that make up a disengagement mechanism of an intuitive differential snow-blower system.
Capstan, from Wrentham, Massachusetts, received the grand prize in the lawn & garden/off-highway category for copper-steel parts that make up a disengagement mechanism of an intuitive differential snow-blower system.

By Liz Nickels

As a metal forming technology, PM gives designers the freedom to conceive shapes that are impractical to achieve in traditional metal-cutting processes, empowering designers to envision new product features with confidence. By continuing to push the boundaries of complexity, tolerances, and mechanical properties, PM fabricators are able to expand into new applications extend their opportunities within existing applications. Covering both conventional press-and-sinter or metal injection moulded parts, the awards recognise the best of the best.

Grand prize awards 

Indo-US MIM Tec Pvt Ltd, from Bangalore, India, earned the grand prize in the automotive – engine category for four MIM parts – blank discharge check, stop discharge check valve, valve discharge check, and CRV spring seat – that go into a device that controls fuel flow in gasoline direct injection, or GDI, pumps, made for Stanadyne Corporation. Three of the parts are made of 440C stainless steel, while the fourth is made of 17-4 PH. The complex geometry of the blank discharge check, with the intercrossing of holes, required tooling with six side cores, three of which move at different timings. This design was judged by the fabricator to be perhaps the most complex, high-volume part ever made by MIM. The customer realised cost savings of close to 35%, while the pump performance was improved by modifying the hole geometry to enhance flow dynamics, with the result being a 10%-to-20% fuel economy boost. 

Keystone Powdered Metal Co, based in St Marys, Pennsylvania, has been awarded a grand prize in the automotive – transmission category for a planetary carrier assembly made for its customer, Ford Motor Company. The 32-part carrier assembly is used in the HF35 hybrid transmission that goes into Lincoln MKZ, Ford C-Max, and Ford Fusion hybrid vehicles. The spider and carrier plate are compacted and then sinterbrazed together before being joined to the shaft. The helical pinion gears are sinter forged to full density using tools that must also rotate and exactly match the gears’ 24.5 degree angle; it is the first time such a gear has been used in an automotive transmission application. It is estimated the customer realised cost savings on the order of 25% by going this route. 

Capstan, from Wrentham, Massachusetts, has received the grand prize in the lawn & garden/off-highway category for copper-steel parts made for General Transmission. The parts make up a disengagement mechanism of an intuitive differential snow-blower system that allows the user to pivot the unit in place by disengaging one of the wheels. These two parts combine to make 11 pressing levels, requiring precisely timed tool motions at ejection, along with sophisticated robotics, for crack-free removal from the lower punches. Despite their shape complexity, these parts are formed to net shape, and specially developed sintering fixtures ensure that flatness and level-to-level relationships are maintained. As a new technology in this product category, this intuitive differential is expected to set the standard for tight-turning requirements for machines of this type. 
 
FloMet LLC, an ARCMIM company located in DeLand, Florida, has earned the grand prize in the medical/dental category for two 5 mm tines – one fixed, one moving – that go into a thermal tissue fusion and dissection system made by its customer, ConMed. The system uses direct thermal energy and pressure to seal, transect, dissect, and coagulate tissue. Fabricated via MIM from 17-4 PH stainless steel, the tines overcame many moulding and processing challenges, including the fixed tine’s length and thin-rib requirements, as well as the need for straightness over its entire length for full functionality with mating components. Innovative tooling and advanced thermal processing techniques were employed to produce two components in a final as-assembled condition with only minimal secondary operations being needed. The fabricator’s expertise in maximizing MIM’s advantages led to the customer redesigning the product to make MIM the preferred manufacturing method.
 
A three-piece assembly also made by FloMet LLC for Shure Incorporated won the grand prize in the electronic/electrical components category. The parts – nozzle interface, outer nozzle, and metal collar – go into high-end sound-isolating earphones that enable user-customizable frequency responses. Made via MIM from 316L stainless steel, the components achieved the objective of producing final net-shape parts that not only met the cost demands of the professional-audio market but maintained a cosmetically perfect surface so critical in a consumer product with a clear exterior. MIM was the ideal choice, as alternative fabrication methods, such as die casting or machining, could not have provided the precision needed at a reasonable cost, nor been able to provide the required material performance.
 

Awards of distinction  

Cloyes Gear & Products Inc, from Paris, Arkansas, won an award of distinction in the automotive – transmission category for a ball ramp actuator comprising a sector gear and fixed ring, made for Magna Powertrain. The actuator applies torque to the front wheels in the BMW high-performance X-Drive transfer case that goes into various BMW platforms. Warm compacted from a hybrid low-alloy steel, the parts replaced forged components that had been used in an earlier transfer case design, and provided 35% cost savings over the forgings. The fabricator delivers in excess of 700,000 actuators annually through this global program. 

Indo-US MIM Tec Pvt Ltd won the award of distinction in the automotive – chassis category for a spur gear made for Magna Closures, Canada. The gear is used in the rear-door assembly of SUVs to enable their opening in the event of loss of automatic control function. Made via MIM from 4605 low-alloy steel, the part replaced a gear that was machined and had the pin welded on, achieving estimated savings of 30% in the process. This gear is an outstanding example of MIM’s ability to meet close tolerances on concentricity and perpendicularity on a part with such a lengthy gear profile. 

Lovejoy Powder Metal Group, from Downers Grove, Illinois, earned an award of distinction in the lawn & garden/off-highway category for a parking/emergency brake piston for hydraulic transmissions used in zero-turn-radius lawn maintenance equipment. Made from FC-0208 iron-copper steel, the piston is compacted with three features on top and six on the bottom, using two upper and three lower punches plus a die shelf. The part is an original design for PM, as its shape makes it impractical for traditional metal-cutting methods. It is pressed and sintered to net shape, requiring no secondary machining operations. 
 
Indo-US MIM Tec Pvt Ltd also received an award of distinction in the hardware/appliances category for these three parts – output shaft, lever, and cover – that are assembled into the quick-change mechanism of a Dremel multitool. The mechanism allows for the swapping of any tool bit within seconds. Made via MIM from 4605 low-alloy steel, the three parts – designed specifically for MIM – are made close to net shape, with only a few secondary operations performed to achieve close tolerances. The complex geometry of the shaft, with three holes intercrossing at 120 degrees, required six side cores per moulding cavity. 
 
A sinter-hardened steel retainer weight made by Hitachi Chemical Co Ltd, Chiba, Japan, has won an award of distinction in the hand tools/recreation category. The part operates in the transmission of large motorcycles, controlling the on/off position of the clutch. The challenge of attaining dimensional accuracy in a component with such a thin, large-diameter shape was overcome with process optimiaation and the choice of steam treatment. This redesign of a previous PM part achieved a 17% weight reduction. The fabricator anticipates this accomplishment could open the door to additional opportunities in the small to medium-size motorcycle market. 
 
Advanced Forming Technology, an ARCMIM company based in Longmont, Colorado, also received an award of distinction in the hand tools/recreation category for a lock hood for a muzzleloading rifle made for its customer Smith and Wesson. Fabricated via MIM from 4605 low-alloy steel, the hood’s complex geometry presents a challenge for maintaining the large U-shape sufficiently undistorted so that it can be coined into final tolerance. This is accomplished using a unique sintering and staging approach that uses an “active” setter made of a feedstock having a similar shrink rate to the hood. The MIM process allowed the customer to offer the rifle at the desired price point in this competitive market. 
 
Another award of distinction in the hand tools/recreation category was given to MPP Ridgway from Ridgway, Pennsylvania, for a bathtub drain tool made for customer ezXtractor. The tool is an assembly of five PM parts – two drain wings, drain top, drain bottom, and drain shaft – all made from FN-0405 modified nickel steel. The design maximizes the benefits of PM technology while simplifying complexity for easy assembly with two circlips and two dowel pins. The two integral cams on the shaft create the action that forces the grippers into the pipe ID. The parts are produced to net shape with two machined grooves for the circlips being the only secondary operations needed. 
 
Smith Metal Products from Center City, Minnesota, won an award of distinction in the medical/dental category for a MIM 17-4 PH stainless steel shaft assembly used in a surgical instrument for passing suture through difficult-to-reach tissue. Unlike most surgical tools, this instrument is single-use, so a precise fabrication process had to be developed that could be scaled up to deliver high volumes at low cost. That process involves moulding the 7 inch shaft in two parts, laser welding them together, and then performing finish machining, ID reaming, heat treating, sand blasting, and passivation to achieve the tightly toleranced dimensions. This method was 4-to-5 times less expensive than Swiss CNC machining would have been. 
 
Indo-US MIM Tec Pvt Ltd also receveid an award of distinction in the medical/dental category for a sound tube used in a hearing aid made by its customer Phonak, Germany. The part’s function is to enhance sound frequency and improve hearing. Fabricated via MIM from 316 stainless steel, the highly complex part achieves all its features in the as-sintered condition, with only glass bead blasting for a better finish performed as a secondary operation. An original design for MIM, it is estimated the part provides 20% cost savings over competing forming processes. The fabricator delivers 500,000 parts annually.