A thin film of 2D halide perovskite crystals of uniform thickness, produced via the novel seeded growth method. Photo: Jeff Fitlow/Rice University.
A thin film of 2D halide perovskite crystals of uniform thickness, produced via the novel seeded growth method. Photo: Jeff Fitlow/Rice University.

Engineers at Rice University have created microscopic seeds for growing remarkably uniform 2D perovskite crystals that are both stable and highly efficient at harvesting electricity from sunlight.

Halide perovskites are organic materials made from abundant, inexpensive ingredients, and Rice's seeded growth method addresses both the performance and production issues that have held back halide perovskite photovoltaic technology.

In a paper in Advanced Materials, chemical engineers from Rice's Brown School of Engineering describe how to make the seeds and use them to grow homogenous thin films. In laboratory tests, photovoltaic devices made from the films proved both efficient and reliable, a previously problematic combination for devices made from either 3D or 2D perovskites.

"We've come up with a method where you can really tailor the properties of the macroscopic films by first tailoring what you put into solution," said study co-author Aditya Mohite, an associate professor of chemical and biomolecular engineering and of materials science and nanoengineering at Rice. "You can arrive at something that is very homogeneous in its size and properties, and that leads to higher efficiency. We got almost state-of-the-art device efficiency for the 2D case of 17%, and that was without optimization. We think we can improve on that in several ways."

Achieving homogenous films of 2D perovskites has proved a huge challenge for the halide perovskite photovoltaic research community, which has grown tremendously over the past decade. "Homogeneous films are expected to lead to optoelectronic devices with both high efficiency and technologically relevant stability," Mohite said.

Rice's seed-grown, high-efficiency photovoltaic films proved quite stable, preserving more than 97% of their peak efficiency after 800 hours under illumination, without any thermal management. In previous research, 3D halide perovskite photovoltaic devices have been highly efficient but prone to rapid degradation, and 2D devices have lacked efficiency but were highly stable.

The Rice study also details the seeded growth process – a method that is within the reach of many labs, said study co-author Amanda Marciel, assistant professor of chemical and biomolecular engineering at Rice. "I think people are going to pick up this paper and say, 'Oh. I'm going to start doing this'. It's a really nice processing paper that goes into depth in a way that hasn't really been done before."

The name perovskite refers both to a specific mineral discovered in Russia in 1839 and to any compound with the same crystal structure as that mineral. For example, halide perovskites can be made by mixing lead, tin and other metals with bromide or iodide salts. Research interest in halide perovskites skyrocketed after their potential for high-efficiency photovoltaics was demonstrated in 2012.

Mohite, who joined Rice in 2018, has researched halide perovskite photovoltaics for more than five years, especially 2D perovskites – flat, almost atomically thin forms of the material that are more stable than their thicker cousins due to an inherent moisture resistance.

He credits study co-lead author Siraj Sidhik, a PhD student in his lab, with the idea of pursuing seeded growth. "The idea that a memory or history – a genetic sort of seed – can dictate material properties is a powerful concept in materials science," Mohite said. "A lot of templating works like this. If you want to grow a single crystal of diamond or silicon, for example, you need a seed of a single crystal that can serve as template."

While seeded growth has often been demonstrated for inorganic crystals and other processes, Mohite said this is the first time it's been shown in organic 2D perovskites.

The process for growing 2D perovskite films from seeds is identical in several respects to the classical process for growing such films. In the traditional method, precursor chemicals are measured out like the ingredients in a kitchen – X parts of ingredient A, Y parts of ingredient B, and so on – and then dissolved in a liquid solvent. The resulting solution is spread onto a flat surface via spin-coating, a widely used technique that relies on centrifugal force to evenly spread liquids across a rapidly spun disk. As the solvent dissolves, the mixed ingredients crystalize into a thin film.

Mohite's group has made 2D perovskite films in this manner for years, and though the films appear perfectly flat to the naked eye, they are uneven at the nanometer scale. In some places, the film may be a single crystal in thickness, and in other places, several crystals thick.

"You end up getting something that is completely polydisperse, and when the size changes, the energy landscape changes as well," Mohite said. "What that means for a photovoltaic device is inefficiency, because you lose energy to scattering when charges encounter a barrier before they can reach an electrical contact."

In the seeded growth method, seeds are made by first slow-growing a uniform 2D crystal and then grinding it into a powder. It is this powder that is dissolved into the solvent, rather than the individual precursors, to form the seeds. These seeds contain the same ratio of ingredients as the classical recipe, and the solution is spin-coated onto disks exactly as it would be in the original method. The evaporation and crystallization steps are also identical. But the seeded solution yields films with a homogeneous, uniform surface, much like that of the material from which the seeds were ground.

When Sidhik initially succeeded with the approach, it wasn't immediately clear why it produced better films. Fortunately, Mohite's lab adjoins Marciel's, and while she and her student, co-lead author Mohammad Samani, had not previously worked with perovskites, they did have the perfect tool for finding and studying any bits of undissolved seeds that might be templating the homogeneous films.

"We could track that nucleation and growth using light-scattering techniques in my group that we typically use to measure sizes of polymers in solution," Marciel said. "That's how the collaboration came to be. We're neighbors in the lab, and we were talking about this, and I was like, 'Hey, I've got this piece of equipment. Let's see how big these seeds are and if we can track them over time, using the same tools we use in polymer science'."

The tool was dynamic light scattering, a mainstay technique in Marciel's group. It revealed that solutions reached an equilibrium state under certain conditions, allowing a portion of some seeds to remain undissolved in solution.

The research showed those bits of seed retained the 'memory' of the perfectly uniform slow-grown crystal from which they were ground, and Samani and Marciel found they could track the nucleation process that would eventually allow the seeds to produce homogeneous thin films.

According to Mohite, this collaboration produced something that is often attempted and rarely achieved in nanomaterials research – a self-assembly method to make macroscopic materials that live up to the promise of the individual nanoparticles of which they are composed.

"This is really the bane of nanomaterials technology," Mohite said. "At an individual, single element level, you have wonderful properties that are orders of magnitude better than anything else, but when you try to put them together into something macroscopic and useful, like a film, those properties just kind of go away because you cannot make something homogeneous, with just those properties that you want.

"We haven't yet done experiments on other systems, but the success with perovskites begs the question of whether this type of seeded approach might work in other systems as well."

This story is adapted from material from Rice University, with editorial changes made by Materials Today. The views expressed in this article do not necessarily represent those of Elsevier. Link to original source.